Consent Preferences
WarningFlammable

M6200

Cuatro calibre de perno para tanques presurizados, columnas o recipientes de hasta 300 PSIG

Application
M6200 Series gauges are widely used to measure liquid levels of fuels, hydraulic fluids, refrigerants, lube oils and cryogenic products in pressurized tanks, columns or vessels up to 300 PSIG [20,7 Bar]. Stainless steel mounting bolts are optional.

General Information & Features
Direct-reading fractional dials, gear actions and aluminum floats are standard models. Remote-reading TwinSite® senders are available for some models. Lever actions are available for centerline mounted models. Nitrile rubber floats are optional. Please refer to instructions on “How to Order” on reverse side of this technical data sheet.

Documents
Data Sheet

Modelo Tipo Montaje Dial de lectura directa estándar Sensor de lectura remota M6281 Jr. Arriba 5323s01793 N/A M6240 Sr. N/A Especifique 0-90 o 240-30 Ohm Twinsite® Senter M6243 C/L o ángulo M6260 Arriba 5025s00570 (lectura lateral) PDMV M6280 5002s00062 M6283 C/L o ángulo M6290 Arriba 5013s00456 (4 ") M6293 C/L o ángulo M6250 El Sr. switchGAUGE Arriba Standard Switch #5023S00778, S.P.S.T., 150 VDC, 1/2 Amp.
Please furnish tank drawings and switch points so proper gauge and
calibration can be supplied. Other switches available, see DS-364. M6253 C/L o ángulo

Opción de costo adicional

1.For a nitrile rubber float, suitable for pressures up to 50 PSIG maximum or 250 PSIG maximum (specify if over 50 PSIG) in place of standard aluminum float, change prefix “M” to “N”.
2.For lever action on C/L mounted gauges only, instead of gear action, add prefix ”L” to the model number.
3. Neoprene Senior gasket, part number 15-836.
4. Viton Senior gasket, part number 15-415.
5. Teflon Senior gasket, part number 15-401.



Especificaciones generales *

Mounting
Gear-action gauges are suitable for top, side, end or angle mounting. Lever-action gauges are suitable for centerline mounting on flat end of tank only.

Accuracy
Accuracy depends upon proper gauge sizing. Junior and Senior dials are ±6%, TwinSite® dials are ±10%. Accuracy may be less for some tank shapes and sizes. Accuracy may be less near full and empty. Accuracy may be less if tank is not level. This gauge is not to be used for filling. All accuracy estimates are expressed as a percent of full scale.

Temperature
Standard operating temperature range -40°F to 158°F, -40°C to 70°C with optional stainless steel mountin bolts which maybe required for temperatures below -20°F, -29°C.

Humidity
For high humidity and marine application, painting of exposed portion of gauge, less dial, is recommended.

Shock
Passes MIL-S-901 B Naval Standard Shock Test.

Vibration
Passes MIL-STD-167 Naval Standard Vibration Test.

Power
0.5 watts maximum for TwinSite® versions.

Tank Pressure
Up to 300 PSIG [20.7 Bar] with standard aluminum float and steel mounting bolts; up to 450 PSIG [31 Bar] with standard aluminum float and stainless steel mounting bolts.

Approvals
Model M6200 direct indicating gauges are available with UL listing for flammable liquids. Models M6253 and M6283 are UL recognized refrigeration components.

NOTE: For installation instructions see MS-501/502 (mounting standard).

Materiales de construcción *

Head
Die-cast aluminum.

Gear Housing
Die-cast aluminum or acetal.

Center Shaft, Support Tube & Float Rod
Tempered aluminum.

Gears, Cross Stud & Bearings
Stainless steel.

Drive Magnet
Alnico.

Float
One-piece aluminum is standard. Nitrile rubber available.

Gasket
UL recognized Buna-N (#15-7 Jr. gasket and #15-4 Sr. gasket.

Standard Direct-Reading Dial
Jr. dial is hermetically sealed polycarbonate.
Sr. dial is aluminum with acrylic crystal, hermetically sealed.

Side-Reading Dial
Aluminum with polycarbonate crystal, hermetically sealed.

TwinSite® Dial
Polyamide.

4″ Dial
Aluminum housing, dial and besel with glass crystall, hermetically sealed.

Mounting Bolts
Zinc-plated steel. (Stainless steel optional.)

Al ordenar especificar

1. Gauge model number.
2. Tank diameter and riser height.
3. Mounting location.
4. Ohm range on TwinSite® versions.
5. Preferred switch on switchgauges, if other than standard.
6. Any listed options, or unlisted preferences.

Consulta de producto-M6200

    Productos relacionados

    Revisado 05-22-2018