Consent Preferences
WarningFlammable

8700 Series Gauge

Acetyl 5 Bolt Gauge with Adjustable Float for Low-Pressure, Non-Heated Systems

Application
The 8700 series gauges are used to measure water levels in all types of low-pressure, non-heated systems. Ideal for boats, recreational vehicles, campers, etc. NOTE: For hot or pressurized water service, see 8400 Series.

General Information & Features
The magnetic construction permits the complete sealing off of the inside liquid from the outside gauge head and dial allowing quick dial replacement without the loss of liquid or time.

The dial pointer is silicone-dampened. All dials, senders, and switches are instantly replaceable — there are just two screws to remove and replace.

The rugged gear drive is standard with shrouded, stainless steel, beveled gears designed to shed and work out any loose particles that might jam the gear action. All materials have been selected to provide outstanding durability in water-gauging applications.

These water gauges are designed for top mounting only. They are equipped with float arms which are to be cut off to the proper length for the tank into which they will be installed. Data sheet DS-337 furnishes the proper cut lengths and instructions on how to install the float and crimp it in place.

This gauge has a 5-bolt SAE pattern flange whichis attached to the tank with five #10 screws througha Buna-N gasket, #0015-00423.

Model Number Magnet Available Dials
8741 Large Alnico Direct-reading dial or TwinSite® sender.
Choice of 0-90, 240-30 Ohms
8781 Small Alnico Direct-reading dial only.

Model Selection Chart

Model Number Mounting Dial, Sender or Switch Data
8741-00008 20.5″ [520] 5323S01834 direct-read P5744S02541
TwinSite® sender, 240-30 Ohms.
8741-00020 26″ [660]

Documents
Data Sheet
MS-533 Installation Instructions
DS-337 Cut-off Dimensions


Tank Depth in Inches Distance from Float Bend to Float Rod Cut-off Point
6 3″
7 3-3/4″
8 4-5/8″
9 5-5/8″
10 6-5/8″
11 7-5/8″
12 8-5/8″
13 9-3/4″
14 10-3/4″
15 11-3/4″
16 12-3/4″
17 13-3/4″
18 14-7/8″
19 15-7/8″
20 16-7/8″
21 17-7/8″
Tank Depth in Inches Distance from Float Bend to Float Rod Cut-off Point
22 18-7/8″
23 20″
24 21″
25 22″
26 23″
27 24″
28 25-1/8″
29 26-1/8″
30 27-1/8″
31 28-1/8″
32 29-1/8″
33 30-1/4″
34 31-1/4″
35 32-1/4″
36 33-1/4″

General Specifications*

Mounting
Recommended for top-mounting only.

Accuracy
Accuracy depends upon proper gauge sizing. Junior dials ±7%, TwinSite® dials ±12%. Accuracy may be less depending upon tank shape. Accuracy may be less near full and empty. Accuracy may be less if tank is not level. This gauge is not to be used for filling. All accuracy estimates are expressed as a percent of full scale.

Temperature
Standard range is -40°F to 158°F, -40°C to 70°C.

Shock & Vibration
Suitable to mobile applications.

Power
0.5 watts maximum for TwinSite® versions.

Tank Pressure
0 to 10 PSIG [0 to 0,68 Bar].

Approvals
UL recognized for marine water service.

Note: Installation Instructions MS-533.

*Materials and specifications are subject to change without notice. Pressure ratings subject to change due to temperature and other environmental considerations.

Materials of Construction*

Head
Lightweight injection molded polyester SAE gasoline gauge flange (2-1/8″ [54] bolt circle for five #10 screws not furnished).

Centershaft, Support Tube & Float Rod
Brass.

Gears, Cross Stud & Bearing

Stainless steel.

Drive Magnet
Plated Alnico.

Gear Housing
Acetal.

Float
Nitrile rubber.

Gasket
Buna-N, 0015-00423.

Direct Reading Dial
Hermetically sealed polycarbonate.

TwinSite® Sender
Polyamide.

Dial Screws
Plastite 0040-00479.

When Ordering Specify:

1. Gauge model number.
2. Choice of dials.

Product Inquiry - 8700 Adjustable

    Related Products

    Revised 05-12-2016