Consent Preferences
WarningFlammable

P6293 系列

消除器 1 "用于在 Bobap、运输和大容量存储应用中更换转子的 NPT 仪表

Application
The Eliminator® direct-reading float gauge is a direct replacement for 1″ NPT rotary-type gauges in LP and NH3 storage tanks. These gauges are designed for larger tanks up to 84″ [2134mm] in diameter. The Eliminator® is not intended for use in filling tanks – its use is restricted to tanks with fixed liquid level gauges, used to determine when the maximum fill level has been reached. The eliminator can be used in mobile applications up to 72″ [1828mm] in diameter.

Documents
Data Sheet
MS-501/502 Installation Instructions
MS-516 Installation Instructions

零件编号 适合坦克尺寸识别
文具/移动 P6293-R4400 高达44英寸 [1210]
文具/移动 P6293-r6000 44.1 "到 60" [1210]-[1524]
固定 P6293-R7200 60.1 "通过 72" [1524]-[1829]
手机 P6293-R7200 60.1 "通过 72" [1524]-[1829]
固定 P6293-8400 72.1 "通过 84" [1829]-[2134]

Any Eliminator installed in a tank greater than 44” is excluded from the Rochester Gauge Limited Warranty.


在安装卡的前阅读完整的警告和注意事项 *

THESE INSTRUCTIONS ARE PREPARED TO ASSIST TRADESMEN AND OTHERS QUALIFIED TO SERVICE LIQUID STORAGE TANK EQUIPMENT. CONSUMERS ARE NOT QUALIFIED TO PERFORM THE INSTALLATION DESCRIBED BELOW. IF YOU HAVE ANY QUESTIONS CONCERNING INSTALLATION OR OPERATION OF THE GAUGE OR GASKET, CONTACT Rochester Sensors. OR ONE OF OUR AUTHORIZED DISTRIBUTORS FOR ASSISTANCE. CHECK SIDE OF GAUGE HEAD FOR MODEL NUMBER AND ASK FOR GAUGE INSTALLATION INSTRUCTIONS FOR YOUR MODEL.


如何进行转换

1. 储罐撤离后, 从头部中心线的 1 "不扩散条约开口中取下旋转仪表。清洁和重新定位女性线。

2. 从挡板上取下两个螺钉。暂时将挡板、螺丝和拨号室放在一边。卸下将仪表头固定在适配器上的四个安装螺钉。

3. 将更换仪表的下部, 包括浮子灯泡、浮臂、齿轮外壳和平衡, 插入油箱开口。

4. 将 1/2 "[12mm] 宽聚四氟乙烯胶带或其他合适的螺纹密封胶的三个包件涂在钢适配器上的 1" NPT 螺纹上, 仪表支撑通过该螺纹。

5. 将适配器拧紧到储罐开口中, 以实现密封接头, 并在水平平面上对齐仪表安装孔。

6. 使用提供的垫圈和四个安装螺钉, 将仪表紧固固定在适配器上。确保仪表是右侧的, 用于定位拨号室的支架选项卡应位于右侧。用交叉图案将安装螺丝均匀地扭矩到140磅, [16, 4Nm]。

7. 使用提供的两个螺丝将4英寸表盘和挡板重新连接到高级®仪表头支架上。

8. 如果您最终将表盘倒置, 则无法通过旋转支架来解决问题。您必须将整个仪表旋转180°。

WARNING: Determine and in­stall the appropriate replacement gauge based on system requirements. The gasket type supplied may not be suitable for all applications and for those applications other gasket materials may be available. The information contained herein is intended for guideline use only and the suitability of any part for a particular application must be determined by the user prior to installation. Improper gauge or gasket selection or application may result in seal failure and subsequent release of tank contents.

WARNING: Even if gauge registers empty, tank may contain high pressure and flammable gas. Do not remove gauge or other pressure containing fittings unless precautions against release of tank contents have been taken. A hazard of fire or explosion may exist if proper methods are not used when removing or installing the gauge or gasket. Replace gasket if gauge is removed. Do not reuse gasket. When reinstalling gauge head align head for proper orientation of the float inside tank. Torque head or mounting screws evenly in several steps based on mounting screw size, gasket material & gauge head size & style.

CAUTION: Improper gauge selection or application may result in inaccurate gauge readings. Release of tank contents as well as damage to equipment and safety hazard may result if tank is overfilled. Fuel exhaustion may occur if tank contents are less than indicated. This gauge is not a substitute for a fixed liquid level gauge or weight measurement device that may be required for filling.

WARNING: Improper APPLICATION, installation, or use of this gauge may cause serious injury or property damage.


建筑材料 *

Head, Gears, Gear Housing, Cros Stud, Bearings & Float
Stainless steel.

Centershaft, Support Tube & Float Rod
Stainless steel.

Drive Magnet
Alnico.

Gasket
Spiral wound, teflon filled, stainless steel.

Adaptor
Cold-rolled steel.

Counterweight
Stainless Steel

订购时指定:

1. Gauge model number.
2. Tank I.D.

WARNING: Carefully ensure that gauge and adapter are adequately protected from damage that might cause leakage of tank contents.

* 材料和规格如有更改, 恕不另行通知。压力额定值可能会因温度和其他环境因素而发生变化。

产品查询-P6293

    相关产品

    2013年05-17-2013 修订